Broken Carbide tip
Moderator: Moderator Group
Broken Carbide tip
I was so excited after replacing some dull tips with some new tips (manufacturer unknown but a Leki rep sold them to me). After 4 miles into the workout, one of the carbide tips was completely ripped out of its plastic housing. Anyone else have this happen? Is there a manufacturer of rollerski ferrules that are better than the rest?
Dave in Nordic Virginia
Re: Broken Carbide tip
Buy from your local retailer, that way the tips would be replaced for free and you are supporting local businesses. 
Exel, One way, Start, and V2 have good roller tips

Exel, One way, Start, and V2 have good roller tips
Re: Broken Carbide tip
Blah wrote:Buy from your local retailer, that way the tips would be replaced for free and you are supporting local businesses.
Exel, One way, Start, and V2 have good roller tips
I hear you - problem is that here in Virginia we have zero retailers. People look at me on the bike path as I'm a total weirdo.
Dave in Nordic Virginia
Re: Broken Carbide tip
I'm not fond of the Exel roller ski ferrules. The heat treat or the material composition is off and I tend to chip the metal on them when I ski hard. The ones I bought recently are a few years old, so maybe they have been improved since.
Re: Broken Carbide tip
DC- I'd wager that most of the people on this site don't have access to a retail shop that carries roller tips, but there are lots of online sites, some of which specialize in rollerskiing stuff.
I think you may have used too much heat when installing your ferrules and compromised the adhesive that was used to secure the carbide tips.
And lots of us don't live in snow country. I remember several years ago rollerskiing in Griffith Park, in LA, with 20 other skiers every Sunday! The Los Angeles demographics have changed a bit since then, but I'm sure there are still guys out there rollersking, and eagerly waiting for that first long drive to Mammouth/Tahoe.
I think you may have used too much heat when installing your ferrules and compromised the adhesive that was used to secure the carbide tips.
And lots of us don't live in snow country. I remember several years ago rollerskiing in Griffith Park, in LA, with 20 other skiers every Sunday! The Los Angeles demographics have changed a bit since then, but I'm sure there are still guys out there rollersking, and eagerly waiting for that first long drive to Mammouth/Tahoe.
Re: Broken Carbide tip
Chris wrote:I'm not fond of the Exel roller ski ferrules. The heat treat or the material composition is off and I tend to chip the metal on them when I ski hard. The ones I bought recently are a few years old, so maybe they have been improved since.
I use Exel tips, and I found they indeed chip. However, chipping does not prevent them from working decently. I am on my second pair now, the first one lasted about 4 months of rollerskiing about 2-3 times/week, ~18-20K each workout.
I resharpen them after every workout - that helps to prolong their life since they retain their correct shape a bit longer.
Has anyone used the Skike tips? Skikes seem fashionable now, and perhaps their products are of good quality?
Re: Broken Carbide tip
Never had a problem with exel it is all I have ever used for the last 30 years or so.
Re: Broken Carbide tip
Broke another one on Friday. During both incidents I was (1) on super soft asphalt where the ferrule digs in super deep and (2) was traveling fairly fast (~25 KPH). I'm thinking this might be a bad combination. As a solution I'm thinking about outfitting my poles with a "quick release" tip. This way I can bring a spare set and change on the fly if needed (I can't imaging heating a pole tip with a lighter to loosen the glue). Rex and Fischer make them:
Rex: http://finnsisu.com/store/rollerskiing/ ... -8-mm.html
Fischer: https://www.fischersports.com/en_en/tec ... tip-system
Rex: http://finnsisu.com/store/rollerskiing/ ... -8-mm.html
Fischer: https://www.fischersports.com/en_en/tec ... tip-system
Dave in Nordic Virginia
Re: Broken Carbide tip
Your doing something wrong. You must be hammering them into the ground or something . Let them touch down before you apply pressure.
Who is online
Users browsing this forum: No registered users and 1 guest